Software release 2.3.0.4_0.432

Validation for System : VISTA04_S / Testhead 1

System Name: VISTA04_S

Configured System Type: MT1101

Testhead 1

FICM Memory Size: 4096K

PIN MODULE CONFIGURATION

________________________

Pin Test head

Module Chassis Position Type FTC Dutmap file

________________________________________________________________

1 A 1 Digital level 3/4 3894060_00.dut

2 A 2 Digital level 3/4 3894060_00.dut

3 A 3 Digital level 3/4 3894060_00.dut

4 A 4 Digital level 3/4 3894060_00.dut

PIN GROUP IDENTIFICATION

________________________

Pin Module 1 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg

Pin Module 2 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg

Pin Module 3 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg

Pin Module 4 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg

1151 POWER SUPPLY CONFIGURATION

_______________________________

Test Head Power 1151 Supply

Chassis Supply Chassis Slot Type

____________________________________________________________

A PS 1 1 1 TEK/1171:V1.01

A PS 2 1 2 TEK/1171:V1.01

A PS 3 1 3 TEK/1171:V1.01

A PS 4 1 4 TEK/1171:V1.01

A PS 5 1 5 TEK/1172:V1.01

A PS 6 1 6 TEK/1172:V1.01

A PS 7 1 7 TEK/1171:V1.01

Start Time: Sat Sep 21 12:50:32 2002

Testhead 1 / Chassis A

Initializing VistaSTANDARD using 3894060_00.dut .....(SPARC controlled)

Testing Calibration Sequencer ... PASS

Reading data from Nonvolatile RAM board

Correction data for CT010074T created Fri Aug 9, 2002

Counter negative slope error = 64 ps

Page 1

Credence_Vista_MS28_validate.txt.log

Edge position DAC offset = 1.938 mV

low level table min = -0.952 V

low level table max = 3.144 V

low level table lsb = 1.000 mV

high level table min = 2.048 V

high level table max = 6.144 V

high level table lsb = 1.000 mV

hic_skew = 250 ps

hiclv_skew = 250 ps

loc_skew = 500 ps

lochv_skew = 500 ps

50 ohm path normalization delay = 0x652d

75 ohm path normalization delay = 0x652d

.....done

Cal is locating calibration fixture origin pad - stand by

Writing data to Nonvolatile RAM board

Writing data to Nonvolatile RAM board

Alignment check missed X+, Y- location pad

Things to check:

Dutmap file is correct for Calibration fixture in use

1 Kohm resistor at Alignment point is correct value

Do you want to try the origin location again? (y, n, help, exit) -->

Inlet air temperature: 24.6C(76F)

I/O Path

PROBER TO TESTHEAD CONTACT TEST

PASS

LOAD REED CONTROL TEST

PASS

PMU GUARD TEST

PASS

PMU REMOTE SENSING TEST

PASS

Common Module

Analog I/O

Analog I/O(pins 1 - 256)

PMU FORCE VOLTAGE RESOLUTION TEST

(Testing on pin #1)

PASS

Page 2

Credence_Vista_MS28_validate.txt.log

DRIVER RESOLUTION TEST

(Testing on pin #1)

PASS

ACTIVE LOAD CLAMP RESOLUTION TEST

(Testing on pin #1)

PASS

TRIGGER COUNTER OPERATION

(Testing on pin #1)

PASS

ERROR_STOP ENABLE TEST

PASS

Digital Pin/Support Module 1

I/O REEDS TEST

PASS

Cycle/Sequence timing

SEQUENCE LENGTH COUNTER OPERATION

(Testing on pin #1)

PASS

CYCLE LENGTH COUNTER

(Testing on pin #1)

PASS

MIN/MAX CYCLE TIME

(Testing on pin #1)

PASS

CYCLE LENGTH STRETCH OPERATION

(Testing on pin #1)

PASS

CYCLE TIME TIMING SET SWITCHING

(Testing on pin #1)

PASS

CYCLE TIME TIMING SET SWITCHING(minimum step)

(Testing on pin #1)

PASS

PERIOD ACCURACY

PASS

Pin Group 1 (pins 1 - 8)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #1)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #1)

PASS

Page 3

Credence_Vista_MS28_validate.txt.log

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #1)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #1)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #1)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #1)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

Page 4

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.2C(76F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

Page 5

Credence_Vista_MS28_validate.txt.log

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 2 (pins 9 - 16)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #9)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #9)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #9)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #9)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #9)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #9)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

Page 6

Credence_Vista_MS28_validate.txt.log

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

Page 7

Credence_Vista_MS28_validate.txt.log

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 3 (pins 17 - 24)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #17)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #17)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #17)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #17)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #17)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #17)

Page 8

Credence_Vista_MS28_validate.txt.log

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

Page 9

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 4 (pins 25 - 32)

Page 10

Credence_Vista_MS28_validate.txt.log

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #25)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #25)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #25)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #25)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #25)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #25)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

Page 11

Credence_Vista_MS28_validate.txt.log

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Page 12

Credence_Vista_MS28_validate.txt.log

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 5 (pins 33 - 40)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #33)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #33)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #33)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #33)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #33)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #33)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

Page 13

Credence_Vista_MS28_validate.txt.log

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.4C(76F)

PASS

Page 14

Credence_Vista_MS28_validate.txt.log

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 6 (pins 41 - 48)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #41)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #41)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #41)

PASS

PMU FORCE CURRENT ACCURACY TEST

Page 15

Credence_Vista_MS28_validate.txt.log

(Testing on pin #41)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #41)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #41)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

Page 16

Credence_Vista_MS28_validate.txt.log

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

Page 17

Credence_Vista_MS28_validate.txt.log

PASS

HISTORY REGISTER TEST

PASS

Pin Group 7 (pins 49 - 56)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #49)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #49)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #49)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #49)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #49)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #49)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

Page 18

Credence_Vista_MS28_validate.txt.log

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.6C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

Page 19

Credence_Vista_MS28_validate.txt.log

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 8 (pins 57 - 64)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #57)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #57)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #57)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #57)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #57)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #57)

PASS

Driver

DRIVER ACCURACY TEST

Page 20

Credence_Vista_MS28_validate.txt.log

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

Page 21

Credence_Vista_MS28_validate.txt.log

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.3C(76F)

Air temperature at cal time: 24.1C(75F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Functional Test Control

FICM INITIAL MEMORY ADDRESS TEST

PASS

FICM MEMORY ADDRESS READBACK TEST

Page 22

Credence_Vista_MS28_validate.txt.log

PASS

FICM MEMORY LOOP START/END OF LOOP TEST(memory load)

PASS

FICM MEMORY LOOP COUNTER TEST(register load)

PASS

FICM MEMORY LOOP COUNTER TEST(memory load)

PASS

MEMORY REPEAT VECTOR TEST

REPEAT VECTOR

PASS

REPEAT COUNT(register load)

PASS

REPEAT COUNT(memory load)

PASS

FICM MEMORY ADVANCE FLAGS TEST

PASS

FICM MEMORY START ON PASS TEST

PASS

Digital Pin/Support Module 2

I/O REEDS TEST

PASS

Cycle/Sequence timing

SEQUENCE LENGTH COUNTER OPERATION

(Testing on pin #65)

PASS

CYCLE LENGTH COUNTER

(Testing on pin #65)

PASS

MIN/MAX CYCLE TIME

(Testing on pin #65)

PASS

CYCLE LENGTH STRETCH OPERATION

(Testing on pin #65)

PASS

CYCLE TIME TIMING SET SWITCHING

(Testing on pin #65)

Page 23

Credence_Vista_MS28_validate.txt.log

PASS

CYCLE TIME TIMING SET SWITCHING(minimum step)

(Testing on pin #65)

PASS

PERIOD ACCURACY

PASS

Pin Group 1 (pins 65 - 72)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #65)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #65)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #65)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #65)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #65)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #65)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

Page 24

Credence_Vista_MS28_validate.txt.log

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.3C(76F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

Page 25

Credence_Vista_MS28_validate.txt.log

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 2 (pins 73 - 80)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #73)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #73)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #73)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #73)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #73)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #73)

PASS

Driver

Page 26

Credence_Vista_MS28_validate.txt.log

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

Page 27

Credence_Vista_MS28_validate.txt.log

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 3 (pins 81 - 88)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

Page 28

Credence_Vista_MS28_validate.txt.log

(Testing on pin #81)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #81)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #81)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #81)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #81)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #81)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Page 29

Credence_Vista_MS28_validate.txt.log

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.2C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

Page 30

Credence_Vista_MS28_validate.txt.log

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 4 (pins 89 - 96)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #89)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #89)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #89)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #89)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #89)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #89)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

Page 31

Credence_Vista_MS28_validate.txt.log

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

Page 32

Credence_Vista_MS28_validate.txt.log

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 5 (pins 97 - 104)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #97)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #97)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #97)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #97)

PASS

Page 33

Credence_Vista_MS28_validate.txt.log

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #97)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #97)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

Page 34

Credence_Vista_MS28_validate.txt.log

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.2C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

Page 35

Credence_Vista_MS28_validate.txt.log

HISTORY REGISTER TEST

PASS

Pin Group 6 (pins 105 - 112)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #105)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #105)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #105)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #105)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #105)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #105)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

Page 36

Credence_Vista_MS28_validate.txt.log

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.6C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

Page 37

Credence_Vista_MS28_validate.txt.log

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 7 (pins 113 - 120)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #113)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #113)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #113)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #113)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #113)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #113)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

Page 38

Credence_Vista_MS28_validate.txt.log

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Page 39

Credence_Vista_MS28_validate.txt.log

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.2C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 8 (pins 121 - 128)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #121)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #121)

PASS

Page 40

Credence_Vista_MS28_validate.txt.log

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #121)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #121)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #121)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #121)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

Page 41

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.2C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

Page 42

Credence_Vista_MS28_validate.txt.log

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Functional Test Control

FICM INITIAL MEMORY ADDRESS TEST

PASS

FICM MEMORY ADDRESS READBACK TEST

PASS

FICM MEMORY LOOP START/END OF LOOP TEST(memory load)

PASS

FICM MEMORY LOOP COUNTER TEST(register load)

PASS

FICM MEMORY LOOP COUNTER TEST(memory load)

PASS

MEMORY REPEAT VECTOR TEST

REPEAT VECTOR

PASS

REPEAT COUNT(register load)

PASS

REPEAT COUNT(memory load)

PASS

FICM MEMORY ADVANCE FLAGS TEST

PASS

FICM MEMORY START ON PASS TEST

PASS

Digital Pin/Support Module 3

I/O REEDS TEST

PASS

Page 43

Credence_Vista_MS28_validate.txt.log

Cycle/Sequence timing

SEQUENCE LENGTH COUNTER OPERATION

(Testing on pin #129)

PASS

CYCLE LENGTH COUNTER

(Testing on pin #129)

PASS

MIN/MAX CYCLE TIME

(Testing on pin #129)

PASS

CYCLE LENGTH STRETCH OPERATION

(Testing on pin #129)

PASS

CYCLE TIME TIMING SET SWITCHING

(Testing on pin #129)

PASS

CYCLE TIME TIMING SET SWITCHING(minimum step)

(Testing on pin #129)

PASS

PERIOD ACCURACY

PASS

Pin Group 1 (pins 129 - 136)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #129)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #129)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #129)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #129)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #129)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #129)

PASS

Driver

DRIVER ACCURACY TEST

Page 44

Credence_Vista_MS28_validate.txt.log

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

Page 45

Credence_Vista_MS28_validate.txt.log

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 2 (pins 137 - 144)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #137)

PASS

Page 46

Credence_Vista_MS28_validate.txt.log

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #137)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #137)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #137)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #137)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #137)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

Page 47

Credence_Vista_MS28_validate.txt.log

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

Page 48

Credence_Vista_MS28_validate.txt.log

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 3 (pins 145 - 152)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #145)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #145)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #145)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #145)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #145)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #145)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

Page 49

Credence_Vista_MS28_validate.txt.log

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

Page 50

Credence_Vista_MS28_validate.txt.log

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 4 (pins 153 - 160)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #153)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #153)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #153)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #153)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #153)

PASS

Page 51

Credence_Vista_MS28_validate.txt.log

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #153)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

Page 52

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Page 53

Credence_Vista_MS28_validate.txt.log

Pin Group 5 (pins 161 - 168)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #161)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #161)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #161)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #161)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #161)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #161)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

Page 54

Credence_Vista_MS28_validate.txt.log

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

Page 55

Credence_Vista_MS28_validate.txt.log

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 6 (pins 169 - 176)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #169)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #169)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #169)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #169)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #169)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #169)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

Page 56

Credence_Vista_MS28_validate.txt.log

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.3C(76F)

Page 57

Credence_Vista_MS28_validate.txt.log

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 7 (pins 177 - 184)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #177)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #177)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #177)

Page 58

Credence_Vista_MS28_validate.txt.log

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #177)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #177)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #177)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

Page 59

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.8C(77F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

Page 60

Credence_Vista_MS28_validate.txt.log

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 8 (pins 185 - 192)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #185)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #185)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #185)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #185)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #185)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #185)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

Page 61

Credence_Vista_MS28_validate.txt.log

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

Page 62

Credence_Vista_MS28_validate.txt.log

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Functional Test Control

FICM INITIAL MEMORY ADDRESS TEST

PASS

FICM MEMORY ADDRESS READBACK TEST

PASS

FICM MEMORY LOOP START/END OF LOOP TEST(memory load)

PASS

FICM MEMORY LOOP COUNTER TEST(register load)

PASS

FICM MEMORY LOOP COUNTER TEST(memory load)

PASS

MEMORY REPEAT VECTOR TEST

REPEAT VECTOR

PASS

Page 63

Credence_Vista_MS28_validate.txt.log

REPEAT COUNT(register load)

PASS

REPEAT COUNT(memory load)

PASS

FICM MEMORY ADVANCE FLAGS TEST

PASS

FICM MEMORY START ON PASS TEST

PASS

Digital Pin/Support Module 4

I/O REEDS TEST

PASS

Cycle/Sequence timing

SEQUENCE LENGTH COUNTER OPERATION

(Testing on pin #193)

PASS

CYCLE LENGTH COUNTER

(Testing on pin #193)

PASS

MIN/MAX CYCLE TIME

(Testing on pin #193)

PASS

CYCLE LENGTH STRETCH OPERATION

(Testing on pin #193)

PASS

CYCLE TIME TIMING SET SWITCHING

(Testing on pin #193)

PASS

CYCLE TIME TIMING SET SWITCHING(minimum step)

(Testing on pin #193)

PASS

PERIOD ACCURACY

PASS

Pin Group 1 (pins 193 - 200)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #193)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #193)

PASS

Page 64

Credence_Vista_MS28_validate.txt.log

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #193)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #193)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #193)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #193)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

Page 65

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.8C(77F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

Page 66

Credence_Vista_MS28_validate.txt.log

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 2 (pins 201 - 208)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #201)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #201)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #201)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #201)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #201)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #201)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

Page 67

Credence_Vista_MS28_validate.txt.log

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

Page 68

Credence_Vista_MS28_validate.txt.log

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 3 (pins 209 - 216)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #209)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #209)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #209)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #209)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #209)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #209)

Page 69

Credence_Vista_MS28_validate.txt.log

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

Page 70

Credence_Vista_MS28_validate.txt.log

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.9C(77F)

Air temperature at cal time: 24.4C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 4 (pins 217 - 224)

Page 71

Credence_Vista_MS28_validate.txt.log

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #217)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #217)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #217)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #217)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #217)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #217)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

Page 72

Credence_Vista_MS28_validate.txt.log

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.6C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Page 73

Credence_Vista_MS28_validate.txt.log

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 5 (pins 225 - 232)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #225)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #225)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #225)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #225)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #225)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #225)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

Page 74

Credence_Vista_MS28_validate.txt.log

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.6C(76F)

Air temperature at cal time: 24.3C(76F)

PASS

Page 75

Credence_Vista_MS28_validate.txt.log

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 6 (pins 233 - 240)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #233)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #233)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #233)

PASS

PMU FORCE CURRENT ACCURACY TEST

Page 76

Credence_Vista_MS28_validate.txt.log

(Testing on pin #233)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #233)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #233)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

Page 77

Credence_Vista_MS28_validate.txt.log

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.4C(76F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

Page 78

Credence_Vista_MS28_validate.txt.log

PASS

HISTORY REGISTER TEST

PASS

Pin Group 7 (pins 241 - 248)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #241)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #241)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #241)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #241)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #241)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #241)

PASS

Driver

DRIVER ACCURACY TEST

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

Page 79

Credence_Vista_MS28_validate.txt.log

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.5C(76F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

Page 80

Credence_Vista_MS28_validate.txt.log

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Pin Group 8 (pins 249 - 256)

PMU

PMU MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #249)

PASS

PMU FORCE VOLTAGE ACCURACY TEST

(Testing on pin #249)

PASS

PMU MEASURE CURRENT ACCURACY TEST

(Testing on pin #249)

PASS

PMU FORCE CURRENT ACCURACY TEST

(Testing on pin #249)

PASS

PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST

(Testing on pin #249)

PASS

PMU FC / MV MEASURE VOLTAGE ACCURACY TEST

(Testing on pin #249)

PASS

Driver

DRIVER ACCURACY TEST

Page 81

Credence_Vista_MS28_validate.txt.log

PASS

INHIBIT COMPLIANCE TEST

PASS

FORCE FORMATS

PASS

INHIBIT FORMATS

PASS

Comparator

COMPARE THRESHOLD ACCURACY

PASS

COMPARE THRESHOLD ACCURACY(part 2)

PASS

COMPARE FORMATS

PASS

COMPARATOR LATCH TIME(minimum detectable pulse)

PASS

COMPARE STROBE SEPARATION

PASS

Active Load

ACTIVE LOAD BRIDGE MODE TEST

PASS

ACTIVE LOAD CLAMP ACCURACY TEST

PASS

ACTIVE LOAD CLAMP CURRENT TEST

PASS

ACTIVE LOAD FORMATS

PASS

ACTIVE LOAD INHIBIT CONTROL TIMING

PASS

ACTIVE LOAD COMPARE STROBE CONTROL TIMING

PASS

Timing

Page 82

Credence_Vista_MS28_validate.txt.log

EDGE PLACEMENT ACCURACY

Current inlet air temperature: 24.8C(77F)

Air temperature at cal time: 24.5C(76F)

PASS

EDGE COUNTER OPERATION

PASS

EDGE TIMING SET SWITCHING

PASS

EDGE COUNTER TIMING SET SWITCHING

PASS

LT1000+ T_SWITCH EMULATION

PASS

ALTERNATE EDGE TIMING SET SWITCHING

PASS

EDGE SCALING(cycle bridging)

PASS

Functional

FICM MEMORY TO I/O TEST(at 50MHz)

PASS

FICM MEMORY TO I/O TEST(off quantum at 50MHz)

PASS

DOUBLE PULSE MODE FUNCTIONAL(at 50MHz)

PASS

WINDOW COMPARE FUNCTIONAL(at 50MHz)

PASS

HISTORY REGISTER TEST

PASS

Functional Test Control

FICM INITIAL MEMORY ADDRESS TEST

PASS

FICM MEMORY ADDRESS READBACK TEST

Page 83

Credence_Vista_MS28_validate.txt.log

PASS

FICM MEMORY LOOP START/END OF LOOP TEST(memory load)

PASS

FICM MEMORY LOOP COUNTER TEST(register load)

PASS

FICM MEMORY LOOP COUNTER TEST(memory load)

PASS

MEMORY REPEAT VECTOR TEST

REPEAT VECTOR

PASS

REPEAT COUNT(register load)

PASS

REPEAT COUNT(memory load)

PASS

FICM MEMORY ADVANCE FLAGS TEST

PASS

FICM MEMORY START ON PASS TEST

PASS

Active Load Currents

ACTIVE LOAD ACCURACY

PASS

ACTIVE LOAD DEVIATION FROM SET POINT

PASS

1151 POWER SUPPLY TEST

Module PS1 (TEK/1171:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 1)

PASS

Module PS2 (TEK/1171:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 2)

PASS

Module PS3 (TEK/1171:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 3)

PASS

Module PS4 (TEK/1171:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 4)

PASS

Module PS5 (TEK/1172:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 5)

Page 84

Credence_Vista_MS28_validate.txt.log

PASS

Module PS6 (TEK/1172:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 6)

PASS

Module PS7 (TEK/1171:V1.01)

Test Head 1/Chassis A (1151 #1 / slot 7)

PASS

Elapsed time - 2:18: 0

Page 85