|
|
| 2099 Main Rd, Newfield, NJ U.S.A 08344 · 856-697-4400 · Fax: 856-697-1313 · [email protected] | |
| HOME · Employment · Trade Shows · About Us · Contact US · Visiting JMC · Chinese |
 |
||
| Credence Vista Vision XP | ||
|
|
|
CREDENCE VISTA VISION XP |
|
Software release 2.3.0.4_0.432 Validation for System : VISTA04_S / Testhead 1 System Name: VISTA04_S Configured System Type: MT1101 Testhead 1 FICM Memory Size: 4096K PIN MODULE CONFIGURATION ________________________ Pin Test head Module Chassis Position Type FTC Dutmap file ________________________________________________________________ 1 A 1 Digital level 3/4 3894060_00.dut 2 A 2 Digital level 3/4 3894060_00.dut 3 A 3 Digital level 3/4 3894060_00.dut 4 A 4 Digital level 3/4 3894060_00.dut PIN GROUP IDENTIFICATION ________________________ Pin Module 1 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg Pin Module 2 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg Pin Module 3 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg Pin Module 4 wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg wc_pg 1151 POWER SUPPLY CONFIGURATION _______________________________ Test Head Power 1151 Supply Chassis Supply Chassis Slot Type ____________________________________________________________ A PS 1 1 1 TEK/1171:V1.01 A PS 2 1 2 TEK/1171:V1.01 A PS 3 1 3 TEK/1171:V1.01 A PS 4 1 4 TEK/1171:V1.01 A PS 5 1 5 TEK/1172:V1.01 A PS 6 1 6 TEK/1172:V1.01 A PS 7 1 7 TEK/1171:V1.01 Start Time: Sat Sep 21 12:50:32 2002 Testhead 1 / Chassis A Initializing VistaSTANDARD using 3894060_00.dut .....(SPARC controlled) Testing Calibration Sequencer ... PASS Reading data from Nonvolatile RAM board Correction data for CT010074T created Fri Aug 9, 2002 Counter negative slope error = 64 ps Page 1 Credence_Vista_MS28_validate.txt.log Edge position DAC offset = 1.938 mV low level table min = -0.952 V low level table max = 3.144 V low level table lsb = 1.000 mV high level table min = 2.048 V high level table max = 6.144 V high level table lsb = 1.000 mV hic_skew = 250 ps hiclv_skew = 250 ps loc_skew = 500 ps lochv_skew = 500 ps 50 ohm path normalization delay = 0x652d 75 ohm path normalization delay = 0x652d .....done Cal is locating calibration fixture origin pad - stand by Writing data to Nonvolatile RAM board Writing data to Nonvolatile RAM board Alignment check missed X+, Y- location pad Things to check: Dutmap file is correct for Calibration fixture in use 1 Kohm resistor at Alignment point is correct value Do you want to try the origin location again? (y, n, help, exit) --> Inlet air temperature: 24.6C(76F) I/O Path PROBER TO TESTHEAD CONTACT TEST PASS LOAD REED CONTROL TEST PASS PMU GUARD TEST PASS PMU REMOTE SENSING TEST PASS Common Module Analog I/O Analog I/O(pins 1 - 256) PMU FORCE VOLTAGE RESOLUTION TEST (Testing on pin #1) PASS Page 2 Credence_Vista_MS28_validate.txt.log DRIVER RESOLUTION TEST (Testing on pin #1) PASS ACTIVE LOAD CLAMP RESOLUTION TEST (Testing on pin #1) PASS TRIGGER COUNTER OPERATION (Testing on pin #1) PASS ERROR_STOP ENABLE TEST PASS Digital Pin/Support Module 1 I/O REEDS TEST PASS Cycle/Sequence timing SEQUENCE LENGTH COUNTER OPERATION (Testing on pin #1) PASS CYCLE LENGTH COUNTER (Testing on pin #1) PASS MIN/MAX CYCLE TIME (Testing on pin #1) PASS CYCLE LENGTH STRETCH OPERATION (Testing on pin #1) PASS CYCLE TIME TIMING SET SWITCHING (Testing on pin #1) PASS CYCLE TIME TIMING SET SWITCHING(minimum step) (Testing on pin #1) PASS PERIOD ACCURACY PASS Pin Group 1 (pins 1 - 8) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #1) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #1) PASS Page 3 Credence_Vista_MS28_validate.txt.log PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #1) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #1) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #1) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #1) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS Page 4 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.2C(76F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS Page 5 Credence_Vista_MS28_validate.txt.log DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 2 (pins 9 - 16) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #9) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #9) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #9) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #9) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #9) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #9) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY Page 6 Credence_Vista_MS28_validate.txt.log PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING Page 7 Credence_Vista_MS28_validate.txt.log PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 3 (pins 17 - 24) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #17) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #17) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #17) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #17) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #17) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #17) Page 8 Credence_Vista_MS28_validate.txt.log PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS Page 9 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 4 (pins 25 - 32) Page 10 Credence_Vista_MS28_validate.txt.log PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #25) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #25) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #25) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #25) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #25) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #25) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION Page 11 Credence_Vista_MS28_validate.txt.log PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Page 12 Credence_Vista_MS28_validate.txt.log Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 5 (pins 33 - 40) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #33) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #33) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #33) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #33) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #33) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #33) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS Page 13 Credence_Vista_MS28_validate.txt.log INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.4C(76F) PASS Page 14 Credence_Vista_MS28_validate.txt.log EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 6 (pins 41 - 48) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #41) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #41) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #41) PASS PMU FORCE CURRENT ACCURACY TEST Page 15 Credence_Vista_MS28_validate.txt.log (Testing on pin #41) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #41) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #41) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST Page 16 Credence_Vista_MS28_validate.txt.log PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) Page 17 Credence_Vista_MS28_validate.txt.log PASS HISTORY REGISTER TEST PASS Pin Group 7 (pins 49 - 56) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #49) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #49) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #49) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #49) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #49) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #49) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS Page 18 Credence_Vista_MS28_validate.txt.log COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.6C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS Page 19 Credence_Vista_MS28_validate.txt.log ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 8 (pins 57 - 64) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #57) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #57) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #57) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #57) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #57) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #57) PASS Driver DRIVER ACCURACY TEST Page 20 Credence_Vista_MS28_validate.txt.log PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing Page 21 Credence_Vista_MS28_validate.txt.log EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.3C(76F) Air temperature at cal time: 24.1C(75F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Functional Test Control FICM INITIAL MEMORY ADDRESS TEST PASS FICM MEMORY ADDRESS READBACK TEST Page 22 Credence_Vista_MS28_validate.txt.log PASS FICM MEMORY LOOP START/END OF LOOP TEST(memory load) PASS FICM MEMORY LOOP COUNTER TEST(register load) PASS FICM MEMORY LOOP COUNTER TEST(memory load) PASS MEMORY REPEAT VECTOR TEST REPEAT VECTOR PASS REPEAT COUNT(register load) PASS REPEAT COUNT(memory load) PASS FICM MEMORY ADVANCE FLAGS TEST PASS FICM MEMORY START ON PASS TEST PASS Digital Pin/Support Module 2 I/O REEDS TEST PASS Cycle/Sequence timing SEQUENCE LENGTH COUNTER OPERATION (Testing on pin #65) PASS CYCLE LENGTH COUNTER (Testing on pin #65) PASS MIN/MAX CYCLE TIME (Testing on pin #65) PASS CYCLE LENGTH STRETCH OPERATION (Testing on pin #65) PASS CYCLE TIME TIMING SET SWITCHING (Testing on pin #65) Page 23 Credence_Vista_MS28_validate.txt.log PASS CYCLE TIME TIMING SET SWITCHING(minimum step) (Testing on pin #65) PASS PERIOD ACCURACY PASS Pin Group 1 (pins 65 - 72) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #65) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #65) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #65) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #65) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #65) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #65) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) Page 24 Credence_Vista_MS28_validate.txt.log PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.3C(76F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS Page 25 Credence_Vista_MS28_validate.txt.log LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 2 (pins 73 - 80) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #73) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #73) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #73) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #73) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #73) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #73) PASS Driver Page 26 Credence_Vista_MS28_validate.txt.log DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING Page 27 Credence_Vista_MS28_validate.txt.log PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 3 (pins 81 - 88) PMU PMU MEASURE VOLTAGE ACCURACY TEST Page 28 Credence_Vista_MS28_validate.txt.log (Testing on pin #81) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #81) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #81) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #81) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #81) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #81) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Page 29 Credence_Vista_MS28_validate.txt.log Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.2C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) Page 30 Credence_Vista_MS28_validate.txt.log PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 4 (pins 89 - 96) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #89) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #89) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #89) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #89) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #89) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #89) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS Page 31 Credence_Vista_MS28_validate.txt.log PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS Page 32 Credence_Vista_MS28_validate.txt.log EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 5 (pins 97 - 104) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #97) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #97) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #97) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #97) PASS Page 33 Credence_Vista_MS28_validate.txt.log PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #97) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #97) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS Page 34 Credence_Vista_MS28_validate.txt.log PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.2C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS Page 35 Credence_Vista_MS28_validate.txt.log HISTORY REGISTER TEST PASS Pin Group 6 (pins 105 - 112) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #105) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #105) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #105) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #105) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #105) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #105) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS Page 36 Credence_Vista_MS28_validate.txt.log COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.6C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING Page 37 Credence_Vista_MS28_validate.txt.log PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 7 (pins 113 - 120) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #113) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #113) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #113) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #113) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #113) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #113) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST Page 38 Credence_Vista_MS28_validate.txt.log PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Page 39 Credence_Vista_MS28_validate.txt.log Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.2C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 8 (pins 121 - 128) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #121) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #121) PASS Page 40 Credence_Vista_MS28_validate.txt.log PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #121) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #121) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #121) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #121) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS Page 41 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.2C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS Page 42 Credence_Vista_MS28_validate.txt.log DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Functional Test Control FICM INITIAL MEMORY ADDRESS TEST PASS FICM MEMORY ADDRESS READBACK TEST PASS FICM MEMORY LOOP START/END OF LOOP TEST(memory load) PASS FICM MEMORY LOOP COUNTER TEST(register load) PASS FICM MEMORY LOOP COUNTER TEST(memory load) PASS MEMORY REPEAT VECTOR TEST REPEAT VECTOR PASS REPEAT COUNT(register load) PASS REPEAT COUNT(memory load) PASS FICM MEMORY ADVANCE FLAGS TEST PASS FICM MEMORY START ON PASS TEST PASS Digital Pin/Support Module 3 I/O REEDS TEST PASS Page 43 Credence_Vista_MS28_validate.txt.log Cycle/Sequence timing SEQUENCE LENGTH COUNTER OPERATION (Testing on pin #129) PASS CYCLE LENGTH COUNTER (Testing on pin #129) PASS MIN/MAX CYCLE TIME (Testing on pin #129) PASS CYCLE LENGTH STRETCH OPERATION (Testing on pin #129) PASS CYCLE TIME TIMING SET SWITCHING (Testing on pin #129) PASS CYCLE TIME TIMING SET SWITCHING(minimum step) (Testing on pin #129) PASS PERIOD ACCURACY PASS Pin Group 1 (pins 129 - 136) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #129) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #129) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #129) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #129) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #129) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #129) PASS Driver DRIVER ACCURACY TEST Page 44 Credence_Vista_MS28_validate.txt.log PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing Page 45 Credence_Vista_MS28_validate.txt.log EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 2 (pins 137 - 144) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #137) PASS Page 46 Credence_Vista_MS28_validate.txt.log PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #137) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #137) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #137) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #137) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #137) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST Page 47 Credence_Vista_MS28_validate.txt.log PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS Page 48 Credence_Vista_MS28_validate.txt.log FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 3 (pins 145 - 152) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #145) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #145) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #145) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #145) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #145) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #145) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator Page 49 Credence_Vista_MS28_validate.txt.log COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING Page 50 Credence_Vista_MS28_validate.txt.log PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 4 (pins 153 - 160) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #153) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #153) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #153) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #153) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #153) PASS Page 51 Credence_Vista_MS28_validate.txt.log PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #153) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS Page 52 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Page 53 Credence_Vista_MS28_validate.txt.log Pin Group 5 (pins 161 - 168) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #161) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #161) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #161) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #161) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #161) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #161) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) Page 54 Credence_Vista_MS28_validate.txt.log PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.3C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) Page 55 Credence_Vista_MS28_validate.txt.log PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 6 (pins 169 - 176) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #169) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #169) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #169) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #169) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #169) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #169) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS Page 56 Credence_Vista_MS28_validate.txt.log FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.3C(76F) Page 57 Credence_Vista_MS28_validate.txt.log PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 7 (pins 177 - 184) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #177) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #177) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #177) Page 58 Credence_Vista_MS28_validate.txt.log PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #177) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #177) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #177) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS Page 59 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.8C(77F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) Page 60 Credence_Vista_MS28_validate.txt.log PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 8 (pins 185 - 192) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #185) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #185) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #185) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #185) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #185) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #185) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) Page 61 Credence_Vista_MS28_validate.txt.log PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS Page 62 Credence_Vista_MS28_validate.txt.log LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Functional Test Control FICM INITIAL MEMORY ADDRESS TEST PASS FICM MEMORY ADDRESS READBACK TEST PASS FICM MEMORY LOOP START/END OF LOOP TEST(memory load) PASS FICM MEMORY LOOP COUNTER TEST(register load) PASS FICM MEMORY LOOP COUNTER TEST(memory load) PASS MEMORY REPEAT VECTOR TEST REPEAT VECTOR PASS Page 63 Credence_Vista_MS28_validate.txt.log REPEAT COUNT(register load) PASS REPEAT COUNT(memory load) PASS FICM MEMORY ADVANCE FLAGS TEST PASS FICM MEMORY START ON PASS TEST PASS Digital Pin/Support Module 4 I/O REEDS TEST PASS Cycle/Sequence timing SEQUENCE LENGTH COUNTER OPERATION (Testing on pin #193) PASS CYCLE LENGTH COUNTER (Testing on pin #193) PASS MIN/MAX CYCLE TIME (Testing on pin #193) PASS CYCLE LENGTH STRETCH OPERATION (Testing on pin #193) PASS CYCLE TIME TIMING SET SWITCHING (Testing on pin #193) PASS CYCLE TIME TIMING SET SWITCHING(minimum step) (Testing on pin #193) PASS PERIOD ACCURACY PASS Pin Group 1 (pins 193 - 200) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #193) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #193) PASS Page 64 Credence_Vista_MS28_validate.txt.log PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #193) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #193) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #193) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #193) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS Page 65 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.8C(77F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS Page 66 Credence_Vista_MS28_validate.txt.log DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 2 (pins 201 - 208) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #201) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #201) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #201) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #201) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #201) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #201) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY Page 67 Credence_Vista_MS28_validate.txt.log PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING Page 68 Credence_Vista_MS28_validate.txt.log PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 3 (pins 209 - 216) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #209) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #209) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #209) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #209) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #209) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #209) Page 69 Credence_Vista_MS28_validate.txt.log PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS Page 70 Credence_Vista_MS28_validate.txt.log ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.9C(77F) Air temperature at cal time: 24.4C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 4 (pins 217 - 224) Page 71 Credence_Vista_MS28_validate.txt.log PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #217) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #217) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #217) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #217) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #217) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #217) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION Page 72 Credence_Vista_MS28_validate.txt.log PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.6C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Page 73 Credence_Vista_MS28_validate.txt.log Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 5 (pins 225 - 232) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #225) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #225) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #225) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #225) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #225) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #225) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS Page 74 Credence_Vista_MS28_validate.txt.log INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.6C(76F) Air temperature at cal time: 24.3C(76F) PASS Page 75 Credence_Vista_MS28_validate.txt.log EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 6 (pins 233 - 240) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #233) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #233) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #233) PASS PMU FORCE CURRENT ACCURACY TEST Page 76 Credence_Vista_MS28_validate.txt.log (Testing on pin #233) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #233) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #233) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST Page 77 Credence_Vista_MS28_validate.txt.log PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.4C(76F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) Page 78 Credence_Vista_MS28_validate.txt.log PASS HISTORY REGISTER TEST PASS Pin Group 7 (pins 241 - 248) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #241) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #241) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #241) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #241) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #241) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #241) PASS Driver DRIVER ACCURACY TEST PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS Page 79 Credence_Vista_MS28_validate.txt.log COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.5C(76F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS Page 80 Credence_Vista_MS28_validate.txt.log ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Pin Group 8 (pins 249 - 256) PMU PMU MEASURE VOLTAGE ACCURACY TEST (Testing on pin #249) PASS PMU FORCE VOLTAGE ACCURACY TEST (Testing on pin #249) PASS PMU MEASURE CURRENT ACCURACY TEST (Testing on pin #249) PASS PMU FORCE CURRENT ACCURACY TEST (Testing on pin #249) PASS PMU FC / MV COMPLIANCE VOLTAGE ACCURACY TEST (Testing on pin #249) PASS PMU FC / MV MEASURE VOLTAGE ACCURACY TEST (Testing on pin #249) PASS Driver DRIVER ACCURACY TEST Page 81 Credence_Vista_MS28_validate.txt.log PASS INHIBIT COMPLIANCE TEST PASS FORCE FORMATS PASS INHIBIT FORMATS PASS Comparator COMPARE THRESHOLD ACCURACY PASS COMPARE THRESHOLD ACCURACY(part 2) PASS COMPARE FORMATS PASS COMPARATOR LATCH TIME(minimum detectable pulse) PASS COMPARE STROBE SEPARATION PASS Active Load ACTIVE LOAD BRIDGE MODE TEST PASS ACTIVE LOAD CLAMP ACCURACY TEST PASS ACTIVE LOAD CLAMP CURRENT TEST PASS ACTIVE LOAD FORMATS PASS ACTIVE LOAD INHIBIT CONTROL TIMING PASS ACTIVE LOAD COMPARE STROBE CONTROL TIMING PASS Timing Page 82 Credence_Vista_MS28_validate.txt.log EDGE PLACEMENT ACCURACY Current inlet air temperature: 24.8C(77F) Air temperature at cal time: 24.5C(76F) PASS EDGE COUNTER OPERATION PASS EDGE TIMING SET SWITCHING PASS EDGE COUNTER TIMING SET SWITCHING PASS LT1000+ T_SWITCH EMULATION PASS ALTERNATE EDGE TIMING SET SWITCHING PASS EDGE SCALING(cycle bridging) PASS Functional FICM MEMORY TO I/O TEST(at 50MHz) PASS FICM MEMORY TO I/O TEST(off quantum at 50MHz) PASS DOUBLE PULSE MODE FUNCTIONAL(at 50MHz) PASS WINDOW COMPARE FUNCTIONAL(at 50MHz) PASS HISTORY REGISTER TEST PASS Functional Test Control FICM INITIAL MEMORY ADDRESS TEST PASS FICM MEMORY ADDRESS READBACK TEST Page 83 Credence_Vista_MS28_validate.txt.log PASS FICM MEMORY LOOP START/END OF LOOP TEST(memory load) PASS FICM MEMORY LOOP COUNTER TEST(register load) PASS FICM MEMORY LOOP COUNTER TEST(memory load) PASS MEMORY REPEAT VECTOR TEST REPEAT VECTOR PASS REPEAT COUNT(register load) PASS REPEAT COUNT(memory load) PASS FICM MEMORY ADVANCE FLAGS TEST PASS FICM MEMORY START ON PASS TEST PASS Active Load Currents ACTIVE LOAD ACCURACY PASS ACTIVE LOAD DEVIATION FROM SET POINT PASS 1151 POWER SUPPLY TEST Module PS1 (TEK/1171:V1.01) Test Head 1/Chassis A (1151 #1 / slot 1) PASS Module PS2 (TEK/1171:V1.01) Test Head 1/Chassis A (1151 #1 / slot 2) PASS Module PS3 (TEK/1171:V1.01) Test Head 1/Chassis A (1151 #1 / slot 3) PASS Module PS4 (TEK/1171:V1.01) Test Head 1/Chassis A (1151 #1 / slot 4) PASS Module PS5 (TEK/1172:V1.01) Test Head 1/Chassis A (1151 #1 / slot 5) Page 84 Credence_Vista_MS28_validate.txt.log PASS Module PS6 (TEK/1172:V1.01) Test Head 1/Chassis A (1151 #1 / slot 6) PASS Module PS7 (TEK/1171:V1.01) Test Head 1/Chassis A (1151 #1 / slot 7) PASS Elapsed time - 2:18: 0 Page 85
|